Carbon steel in the UAE is the pipe, plate, bar and coil behind most process piping, pressure vessels, tanks and fabrication in ADNOC plants, utilities and workshops. This page lists UAE carbon steel suppliers and explains the grades buyers specify (ASTM A106, A333, A516, EN 10028), when low-temperature and HIC or SSC testing is needed, which approvals apply, and what moves price and delivery.
0 suppliers found · 4 subcategories
Skip the search. Post your requirement and we'll connect you with verified carbon steel suppliers who quote for your order directly.
Tell us about carbon steel in UAE and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Carbon steel is iron alloyed mainly with carbon and manganese, and in the UAE it is the default material for process piping, pressure vessels, storage tanks, skids and general fabrication wherever the fluid is not corrosive enough to justify stainless or alloy grades. It sits under the wider steel products category for the UAE, next to stainless steel for chloride and hygienic duty and chromium-molybdenum alloy steel for high-temperature service.
The product form tells you little on its own. What matters on a UAE enquiry is the specification and grade printed on the material requisition, because an ADNOC piping class or a vessel datasheet names exactly one of them, and a substitute needs written approval. The forms ListGCC lists are below, with the specifications that appear most often.
| Product | Specifications seen on UAE enquiries | Typical use |
|---|---|---|
| Carbon steel pipes for process and utility lines | ASTM A106 (seamless, high-temperature service), ASTM A333 (low-temperature service with impact testing), API 5L for line pipe | Hydrocarbon and utility piping in gas plants and refineries, firewater, cooling water, steam condensate |
| Carbon steel plates for vessels and tanks | ASTM A516 Grades 55 to 70, EN 10028-2 and EN 10028-3 | Pressure vessel shells and heads, separators, heat exchanger shells, tank shells and floors |
| Carbon steel bars and rods | Mill grade to ASTM or EN; forged pressure parts to ASTM A105 or A350 | Machined parts, shafts, pins, anchor bolts, flange and fitting forgings |
| Carbon steel sheets and coils | Hot-rolled, cold-rolled or galvanised coil to the mill designation and coating mass | Ducting, enclosures, panels, light fabrication and roll forming |
Line pipe for cross-country transmission is covered on the pipeline equipment and materials page, and beams, columns and rebar belong to structural steel for UAE buildings. This page stays with pressure-retaining carbon steel and the stock that workshops buy.
Choose the grade from the design temperature range and the fluid, not from what the stockist has on the rack. In the UAE the three questions that change the order are: does the line run hot for long periods, can it get cold during a process upset, and does the fluid contain wet hydrogen sulfide.
ASTM A106 covers seamless carbon steel pipe for high-temperature service from NPS 1/8 to NPS 48, suitable for bending, flanging and welding. Its scope carries a note asking the designer to consider possible graphitization, the slow breakdown of carbide that can weaken carbon steel after long exposure at elevated temperature. On hot UAE refinery and utility lines that note is why piping classes switch to alloy steel above a set temperature; the cut-off comes from your project piping specification, not from the pipe standard.
Gulf summers make it easy to forget low-temperature design, but the cold comes from the process. Depressurising a gas system, flashing liquids across a valve and refrigerated storage can chill steel well below ambient in minutes. ASTM A333 covers carbon and alloy pipe intended for low temperatures and other applications requiring notch toughness, and its scope warns that some sizes may not be available because heavier walls hurt impact properties. Matching forgings come under ASTM A350, which requires notch toughness testing. If the line list shows a minimum design metal temperature below what ordinary A106 and A105 are qualified for, order impact-tested material and check the test temperature on the certificate.
Much of Abu Dhabi's gas carries hydrogen sulfide, as the oil, gas and petrochemicals sector page for the UAE describes. Wet H2S can crack carbon steel in two ways buyers need to keep apart. Sulfide stress cracking is controlled mainly through hardness limits on base metal and welds. Hydrogen-induced cracking, including stepwise cracking, is a property of the plate or pipe itself and is controlled by clean steelmaking and tested on samples, usually to NACE TM0284. ISO 15156-2:2020 sets requirements for selecting and qualifying carbon and low-alloy steels against these mechanisms; as of 2026 it is published and marked for revision, so quote the edition your ADNOC or EPC specification names. For A516 plate and seamless pipe in sour duty, the requisition should state HIC testing, the acceptance values, any ultrasonic examination and the delivery heat treatment, all taken from the owner material specification.
Pipe and plate stored outdoors near Jebel Ali, Hamriyah or Mussafah collect salt and dust that turn into pitting under paint and inside bores. Cap pipe ends, keep plate off the ground and under cover, and reject stock with heavy pitting on bevels or flange faces. Coating systems for exposed steel are discussed on the structural steel page, so they are not repeated here.
No single UAE regulation approves carbon steel pipe or plate for process use. The rules come from the code the plant is built to, the owner's material specifications and the buyer's vendor list, checked as of 2026.
| Requirement | What it covers | Who applies it |
|---|---|---|
| ASTM A106, A333, A516, A105, A350 | Chemistry, mechanical properties, testing and marking of the material | Named in the piping class or vessel datasheet |
| EN 10028-2 and EN 10028-3 | European pressure plate with elevated temperature properties, or normalized fine grain steels | Vessel designs to European codes; both 2017 editions are marked for revision |
| ASME B31.3 (2024) | Materials, design, fabrication, examination and testing of process piping | ADNOC, EPC contractors and plant owners |
| ISO 15156-2:2020 | Carbon and low-alloy steel in H2S service: SSC, HIC, SOHIC and stepwise cracking | Sour service clauses in owner specifications |
| EN 10204 type 3.1 or 3.2 | The inspection document issued with the material | Purchase order; 3.2 needs an independent or purchaser inspector |
| ADNOC supplier registration and ICV | Who may supply ADNOC group companies and how bids are scored | ADNOC procurement |
| MoIAT conformity schemes (ECAS) | Mandatory certification for products on the regulated list; rebar is the steel product most often caught | Ministry of Industry and Advanced Technology |
For how the ECAS and Emirates Quality Mark schemes work, read our guide to UAE product conformity. For flange and fitting material pairing with the pipe, the pipe fittings and flanges standards guide and the pipe fittings and flanges category carry the detail.
UAE carbon steel reaches site through three channels: mill orders placed directly or through a mill agent, authorised distributors that hold a mill's paperwork, and stockists in Dubai, Sharjah and Abu Dhabi that cut and deliver from local inventory. Stockists win on common A106 Grade B sizes and A516 Grade 70 plate in standard thickness; impact-tested, HIC-tested or large-diameter material normally goes back to a mill.
Brands with carbon steel product lines on ListGCC include Hyundai Steel, which rolls plate and API 5L line pipe, NKK seamless pipe, now within JFE Steel, Sichuan Huagong large-diameter submerged arc welded pipe and Jazeera Steel ERW black and galvanised pipe from Sohar in Oman. Ask any seller whether they are the mill, its appointed distributor or a trader, and ask for certificates that trace to the heat number stamped on the steel.
Practical steps for vetting a supplier are in how to source industrial suppliers in the UAE and Saudi Arabia. If you want several UAE quotes against one material list, post your requirement with grade, size, quantity, testing and certificate type.
Price follows global steel and scrap markets, freight into Jebel Ali or Khalifa Port and the exchange rate, then the extras that turn commodity steel into project steel. Lead time depends mostly on whether the item is on a UAE shelf or needs a mill slot.
Metric rebar sizes and what Gulf mills roll, ASTM bar numbers in mm, what makes a bar deformed, reading the grade from ribs and rolled marks, what a delivery certificate must contain, and what CARES means.
How to buy rebar in the UAE and Saudi Arabia: B500B and Grade 60 explained, UAE ECAS and Saudi Quality Mark rules, bar marks and mill certificates, the main Gulf mills, coated bars and pricing terms.