Powder coatings in the UAE are dry, solvent-free coating powders sprayed electrostatically and oven cured on aluminium windows and facades, steel furniture, enclosures, fencing and fabricated parts. This page lists UAE powder coating suppliers and explains the resin types, how to specify for UAE sun and coastal salt using QUALICOAT and AAMA classes as of 2026, galvanised steel to EN 13438, and what drives cost and lead time.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified powder coatings suppliers who quote for your order directly.
Tell us about powder coatings in UAE and receive competitive quotes from verified suppliers — free, fast, and no obligation.
How to specify powder coating for aluminium and steel in the Gulf: powder chemistries, QUALICOAT and AAMA, licensed coaters in the UAE and Saudi Arabia, colour control and a coater audit checklist.
A powder coating is a finely ground mix of resin, hardener and pigment that is sprayed dry onto earthed metal and then melted and cured in an oven into a continuous film. It contains no solvent, gives an even film in one coat and is the standard finish for architectural aluminium in the UAE. Powders are one product group under industrial paints and coatings for the UAE, and they are bought by extruders and powder coating lines, facade and window fabricators, furniture and shelving makers, panel builders and fabricators of gates, railings and street furniture.
The resin decides where the powder can go. Outdoors in UAE sunlight only polyester and fluoropolymer chemistries keep their colour for long.
| Powder type | Typical UAE use | Key specification points |
|---|---|---|
| Standard polyester (TGIC or TGIC-free) | Windows, doors, railings, fencing, light poles | QUALICOAT class 1 or AAMA 2603, colour and gloss, film thickness |
| Superdurable polyester | Curtain walls, facade panels, louvres on towers | QUALICOAT class 2 or AAMA 2604, seaside pretreatment where coastal |
| Hyper durable and fluoropolymer powders | Landmark facades, high-rise cladding | QUALICOAT class 3 or AAMA 2605, colour warranty terms |
| Epoxy | Interior parts, electrical enclosures, pipe and rebar coatings | Chemical and corrosion resistance, chalks quickly in sun |
| Epoxy-polyester hybrid | Office furniture, racking, appliances, indoor fixtures | Interior only, smooth or textured finish |
| Zinc-rich or epoxy powder primer | Steel under a polyester topcoat, galvanised steel | Two-coat system, outgassing control, EN 13438 for galvanised steel |
For steel that needs more than a powder can give, compare liquid epoxy coatings and protective coating systems for coastal structures. If you need the coating applied rather than the powder, use powder coating services in the UAE; profiles come from aluminium extrusion suppliers and finished frames from aluminium door and window makers.
In the UAE the main threats to a powder coating are UV, which fades colour and dulls gloss, and coastal salt and humidity, which attack the aluminium or steel through any weakness in pretreatment. Pick the durability class for the sun, and the pretreatment for the coast.
Architectural powders are ranked by natural weathering in Florida. Under QUALICOAT, class 1 must lose less than 50 percent of its gloss after 12 months; class 2 must lose less than 25 percent at 12 months, 40 percent at 24 months and 50 percent at 36 months; and class 3 must lose less than 20 percent at three years, 45 percent at seven and 50 percent at ten. Trade sources note class 3 is typically used in extreme climates such as the Middle East. For towers in Dubai Marina, Downtown or on Abu Dhabi's islands, where facades are hard to recoat, class 2 is a common minimum and class 3 or AAMA 2605 for premium buildings.
QUALICOAT treats sites within five kilometres of a coast or tidal estuary as coastal and offers a Seaside Class for every powder class; check its requirements with the coater. Much of Dubai, Abu Dhabi, Sharjah and the northern emirates is within that distance. On aluminium, poor pretreatment shows as corrosion creeping from cut edges and drill holes, so the coating line matters as much as the powder.
Powder on bare steel outdoors needs a primer, often zinc-rich, under the topcoat. On hot-dip galvanised steel, gas trapped in the zinc can blister the powder during curing unless the parts are degassed and a suitable primer is used. EN 13438 sets performance requirements for powder coatings on galvanised and sherardised steel used in construction, and gives guidance on cleaning and pretreatment.
UAE facade and window specifications usually call for a powder approved under QUALICOAT or rated to AAMA 2603, 2604 or 2605, applied by a licensed or approved coater. Galvanised steel uses EN 13438. We checked these standards in October 2026.
| Requirement | Applies to | Authority |
|---|---|---|
| QUALICOAT specifications (26th edition introduction published) | Approval of powders (P-numbers), licensing of coating plants and finished architectural aluminium | QUALICOAT, through national general licensees |
| QUALICOAT class 1, 2 and 3 and Seaside Class | Weathering durability and coastal pretreatment | QUALICOAT |
| AAMA 2603, 2604 and 2605 | Organic coatings on architectural aluminium: 1, 5 and 10 years of South Florida exposure | FGIA (formerly AAMA) |
| EN 13438:2013 | Powder coatings on hot dip galvanised or sherardised steel for construction | CEN |
| MoIAT paints and varnishes scheme | Paints on the UAE market; whether powders are in scope to be confirmed per product | Ministry of Industry and Advanced Technology |
QUALICOAT approval applies to two things: the powder, which gets an approval number, and the coating plant, which is licensed and inspected. A facade specification that names only the powder is incomplete. Ask the coater for a current licence and the powder supplier for the approval certificate. AAMA 2604 and 2605 are written for factory-applied coatings over 1.2 mils (about 30 microns). For product conformity in the UAE, see our ECAS and EQM guide.
For architectural work, buy powder from the manufacturer or its authorised distributor so that batch records, approvals and the colour warranty trace back to the maker. Stockists are fine for standard RAL colours on fabrication jobs where no warranty is needed.
Powder makers in the UAE market include Jotun, whose portfolio includes powder coatings alongside protective paints; AkzoNobel, maker of Interpon powders; PPG, with industrial and powder coatings; and Sherwin-Williams, which also makes powder coatings.
Ask each supplier for:
To source powder or coating capacity, post your powder coating requirement with colours, finish, class and quantity. The guide to sourcing industrial suppliers explains how to check that a distributor is authorised.
Powder price in the UAE rises with durability class, special effects and small batch sizes. Because powder is applied by weight, compare cost per square metre at the specified film thickness, which depends on the powder's specific gravity.
Standard RAL colours in common finishes are usually stocked in the UAE. Special colours for a facade need sampling, approval of master panels and a production batch, so start early in the project.