Casing and tubing in the UAE are the steel pipes run into oil and gas wells: casing lines and supports the hole, and tubing carries production to surface. They are made to API 5CT, with grades from J55 to P110 and sour service L80, and joined by API or premium threads. This page covers grades, connections, ADNOC sourcing and what moves price.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified casing & tubing suppliers who quote for your order directly.
Tell us about casing & tubing in UAE and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Casing is the large diameter steel pipe cemented into the well to hold the hole open, isolate zones and carry the wellhead load. Tubing is the smaller pipe run inside the production casing to carry oil, gas or injected fluid. Together they are called oil country tubular goods (OCTG), and they are the part of the wellhead family listed under wellhead equipment in the UAE that is measured in thousands of metres per well, not in single units.
A land well in Abu Dhabi is built as a nest of strings, each going deeper at a smaller diameter.
| String | Purpose | Selection points |
|---|---|---|
| Conductor | Supports the top of the hole and the wellhead | Large diameter, low grade, connection strength |
| Surface casing | Protects fresh water zones, carries the BOP and wellhead | Collapse and burst, API connection, cement design |
| Intermediate casing | Isolates troublesome formations before the reservoir | Higher grade, sour service where H2S is expected |
| Production casing or liner | Isolates the reservoir and contains the well | Grade, weight, gas-tight premium connection, corrosion allowance |
| Production tubing | Carries production to surface | Diameter, flow, corrosion resistant alloy if CO2 or H2S, premium or API thread |
Pipe in a well is different from pipe in a pipeline. If you are looking at transmission lines, see line pipes and fittings; this page is about pipe that is hung in a hole.
The API 5CT specification is the standard for casing and tubing. The letter marks the steel type and the number is the minimum yield strength in thousands of pounds per square inch (ksi), so P110 has a minimum yield of 110 ksi. API publishes the tenth edition of Specification 5CT alongside the seventh edition of Technical Report 5C3 and says its Monogram audits moved to the tenth edition on 1 July 2019; a later edition may now apply, so check the current one with your supplier. The tenth edition updated N80 Type 1 requirements, added polymer quenching for L80, updated hardness requirements for L80, C90, T95 and C110 based on NACE MR0175, and removed M65.
| Grade family | Typical use | Note |
|---|---|---|
| H40, J55, K55 | Conductor, surface and shallow strings | Lower strength, low cost |
| N80, P110 | Intermediate and production strings in non-sour wells | Higher strength for depth and pressure |
| L80, C90, T95 | Sour service strings where H2S is present | Controlled hardness; NACE MR0175 sets the limits |
| Q125 | Deep, high pressure strings | Not for sour wells |
| Chrome alloys such as L80 13Cr | CO2 corrosion resistance | Higher cost; confirm the type with the well team |
Treat the table as a guide to families and let the well engineer set grade, weight and connection. The wellhead below sits to API 6A, which is explained in the parent page.
Pipe lengths are joined by threads cut on each end and a coupling, or by integral threads. API round and buttress threads are common for surface and many intermediate strings. For gas wells, high pressure and sour reservoirs, operators use premium connections with metal to metal seals, which are proprietary and bought from the pipe maker.
Connection care decides whether the well stays tight. Thread compounds (dope) prevent galling and help seal, and they must match the connection and well temperature. BESTOLIFE makes thread compounds and anti-seize greases used on OCTG and rotary shouldered connections, and Jet-Lube makes Kopr-Kote, Eco-Safe and other OCTG thread compounds. Centralizers keep casing off the wall during cementing; Maxwell Oil Tools makes composite casing centralizers and stop collars. Tubular running services and drilling-with-casing systems are offered by Weatherford.
Most casing problems show up on the rig floor, not in the specification. The crew makes up each joint to a torque or a torque and turn window, stabs it carefully so the threads do not cross, and runs at a speed set by the surge pressure the hole can tolerate. Centralizers are spaced to keep the string off the wall so the cement can surround it, and float equipment lets the string fill as it goes down. Buyers who treat pipe, dope, centralizers and running service as one package, with one point of responsibility for connection integrity, have fewer disputes when a joint leaks on test.
For the largest buyer, the route is a framework contract. In August 2019 ADNOC announced three OCTG contracts with a combined scope of AED 13.2 billion (about 3.6 billion US dollars) for one million metric tons of casing and tubing over five years. They went to Consolidated Suppliers Establishment (representing Tenaris), Abu Dhabi Oilfield Services Company (representing Vallourec) and Habshan Trading Company (representing Marubeni). ADNOC said the awards carried potential In-Country Value above 50 percent and more than AED 367 million of foreign direct investment over five years for an OCTG threading plant, a repair centre and a training academy in Abu Dhabi.
Other operators, drilling contractors and service companies buy through distributors, stockists and mills. Two makers listed on ListGCC cover API 5CT: NKK seamless pipes (part of JFE Steel) lists API 5CT seamless casing and tubing, and Hyundai Steel lists API 5CT seamless and ERW casing. Buying direct from a mill makes sense for large lots; stockists make sense for small lots and urgent replacement, where you should insist on mill test certificates traced to heat and pipe number.
As of 2026, there is no UAE product certificate for OCTG. Operators require API 5CT conformity, usually from a mill holding an API Monogram licence, plus their own specifications for inspection and traceability.
| Requirement | Applies to | Who sets it |
|---|---|---|
| API Specification 5CT | Casing and tubing: grades, dimensions, testing, marking | API |
| API Monogram licence | Evidence the manufacturer is audited to the specification | API, requested by operators |
| NACE MR0175 (ISO 15156) | Material limits for sour service | Referenced in 5CT hardness rules for L80, C90, T95 and C110 |
| Operator OCTG specifications | Additional testing, inspection, thread protection, storage | ADNOC group companies and international operators |
| In-Country Value (ICV) certificate | Tender scoring | MoIAT |
Our guide to pipe fitting and flange standards explains the standards used for the surface piping the well connects to.
Downhole conditions decide grade, but storage and handling in the UAE damage pipe before it ever goes in the hole. Pipe racks in coastal yards see salt and humidity, which attack thread protectors and unprotected threads; sun heats stored pipe unevenly; blown sand gets into threads and wrecks sealing surfaces.
Surface pipe preservation is related; see pipe fittings and flanges. When the string is run, the stack on top is the blowout preventers, and the valves on top of the tubing are Christmas trees and wellhead valves.
For quotes from several UAE suppliers, post your requirement with the casing programme attached.