Ultrasonic level sensors in the UAE are non-contact instruments that time a sound pulse to the liquid or solid surface and report level as a 4 to 20 mA signal. They suit water tanks, wet wells, channels and silos. This page covers the types, their limits in heat, foam and steam, ECAS-Ex rules, and what drives price and delivery.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified ultrasonic level sensors suppliers who quote for your order directly.
Tell us about ultrasonic level sensors in UAE and receive competitive quotes from verified suppliers — free, fast, and no obligation.
An ultrasonic level sensor sends a burst of sound down to the surface of a liquid or bulk solid, waits for the echo and converts the travel time into distance, then level. Within level measurement instruments for the UAE it is the low-cost, no-contact option for water, wastewater and simple chemical duties, and the main alternative to radar level transmitters.
| Type | Typical UAE use | Key specification points |
|---|---|---|
| Compact two-wire sensor-transmitter | Water and chemical tanks, small reservoirs, sumps | Range (a few metres), thread size, 4 to 20 mA output, wetted material such as PVDF |
| Transducer with separate transmitter | Pump stations, treatment works, where electronics stay in a panel | Cable length, relay outputs, pump control logic, volume and flow calculation |
| Long-range sensor for tanks and silos | Large tanks, bulk solids bins | Range for liquids and for solids (solids are always shorter), blocking distance, beam angle |
| Open-channel flow sensor | Weirs, flumes, stormwater and effluent channels | Accuracy over range, flow curve, battery or solar supply, IP68 |
| Intrinsically safe version | Fuel, solvent and effluent tanks with flammable vapour | Ex marking, zone and gas group, barrier or supply unit, ECAS-Ex certificate |
To give a sense of scale, Endress+Hauser's Prosonic line lists the compact FMU30 at 2 m or 3.5 m depending on the sensor size, while its FDU92 sensor reaches 20 m in liquids and 10 m in solids and its FDU95 reaches 45 m. Siemens lists its SITRANS Probe LU at 0.2 to 12 m. Ranges for solids are always lower than for liquids, so read both figures on a datasheet.
Ultrasonic sensors fail when the sound cannot make a clean round trip: in foam, dense vapour, dust, strong turbulence, or with a large temperature difference between the sensor and the surface. Every one of these should be on your checklist before you accept the technology.
Sensors compensate for the changing speed of sound with an internal temperature probe, but compensation reads the air at the sensor, not the air column in between. That distinction matters in the next section.
In the UAE the main risk is a hot, sun-loaded air gap above the liquid, followed by condensation on the face and sand on everything. Plan for them at the specification stage rather than at commissioning.
A steel tank roof in August can heat the air under it far above the liquid temperature. That is exactly the layering that causes attenuation and drifting readings. For outdoor tanks in direct sun, radar is the safer technology; ultrasonic fits shaded, covered or underground structures such as wet wells, sump chambers and covered reservoirs. If you must use ultrasonic outdoors, add a sun shield, mount the sensor on the shaded side and ask the supplier for the maximum ambient on the datasheet. Endress+Hauser lists -20 to 60 degrees C for the FMU30 and up to 95 degrees C for the FDU92 sensor, so the choice of model matters.
Night humidity on the coast condenses on the face. Siemens describes the SITRANS Probe LU as having a self-cleaning ultrasonic face that resists build-up, cobwebs, wind and vibration, with an IP68 potted PVDF sensor. Endress+Hauser describes a similar vibrating-diaphragm self-cleaning effect for Prosonic. Neither removes the need for a cleaning round after a shamal sand event.
Lift stations and wet wells combine humidity, corrosive gases and splashing. Choose a chemically resistant wetted material (PVDF is common), a sealed cable gland and a mounting that keeps the sensor clear of inlet cascades. Treatment-works duties are covered under wastewater treatment.
Pick ultrasonic for continuous, non-contact level in clean or lightly contaminated liquids at moderate range; pick another technology when foam, steam or pressure rule out sound. The comparison below uses the sibling category pages.
As of 2026, a general-purpose ultrasonic sensor in a water tank needs normal product conformity, while any sensor in a flammable atmosphere needs an ECAS-Ex certificate based on IECEx documents. Confirm scope with the Ministry of Industry and Advanced Technology (MoIAT) or your certifier before ordering.
| Requirement | Applies to | Authority or body |
|---|---|---|
| ECAS-Ex certificate of conformity under Cabinet Resolution No. 23 of 2016 | Electrical measurement devices used in explosive atmospheres | MoIAT, through notified bodies such as Intertek |
| IECEx test certificate, test report and quality audit report | Technical basis for ECAS-Ex | IECEx certification bodies |
| Wireless adapters such as Bluetooth | Models that add a radio option | TDRA radio registration, confirm per model |
| Owner approved vendor lists | Utilities, oil and gas and municipal projects | Project owner |
Intertek states that the ECAS-Ex certificate of conformity is issued with a one-year or three-year validity. Unlike radar, an ultrasonic sensor emits sound rather than radio waves, but Siemens offers an optional Bluetooth adapter for the Probe LU, so check any wireless accessory separately. The guide to ECAS and EQM conformity in the UAE explains the registration steps.
Ultrasonic level sensors in the UAE come from instrument manufacturers' regional offices, their authorised distributors and general instrumentation stockists, with common compact models held in local stock. Brands with an ultrasonic range include:
Check product lifecycle before specifying. Endress+Hauser lists its FMU40, FMU41 and FMU42 sensors as being phased out, with successors named on its page, so a spare-parts plan matters for installed bases. The guide to sourcing industrial suppliers in the UAE and Saudi Arabia explains how to vet a distributor.
Price follows range, wetted material, outputs and certification more than brand alone; lead time follows whether the model is stocked in the UAE.
To compare offers from UAE suppliers, post your requirement with medium, tank height, blocking distance, maximum temperature and any hazardous-area marking.