Rubber seals and gaskets in the UAE are the flat gaskets, moulded rings and extruded profiles that close flanges, covers, doors and housings against water, air, oil and dust. This page covers the main forms, how to choose between EPDM, NBR and other compounds for UAE heat, sun and fluids, how to store them, and what drives price and delivery.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified rubber seals & gaskets suppliers who quote for your order directly.
Tell us about rubber seals & gaskets in UAE and receive competitive quotes from verified suppliers — free, fast, and no obligation.
A rubber seal or gasket is a compressible elastomer part that fills the gap between two surfaces so fluid or air cannot pass. The family sits within industrial rubber products in the UAE, and it overlaps with the broader seals and gaskets category, which covers mechanical seals and metallic gaskets. This page is about the elastomer end: flat cut gaskets, moulded parts and extruded strip.
For the small round rings that seal shafts and grooves, go to the dedicated page on O-rings and oil seals. Here the focus is the larger and less standardised parts that workshops cut, mould or extrude to a drawing.
| Form | Typical UAE use | What to specify |
|---|---|---|
| Flat cut gasket (full face or ring) | Chilled water, cooling water and drain flanges; pump and valve covers | Flange standard and size, thickness, compound, hardness, fabric insertion |
| Moulded seal | Manhole covers, hatch seals, custom housings, grommets | Drawing or sample, compound, tolerance class, tooling |
| Extruded profile and strip | Doors of cold rooms and enclosures, glazing, panels, switchgear cabinets | Profile section, length, joint method, adhesive backing |
| Rubber sheet for cutting on site | Maintenance gaskets, plant repairs | Compound, thickness, roll or sheet size |
| Sealing washers and bonded seals | Fittings, hydraulic and water connections | Size, metal insert, pressure rating |
Choose the compound by the fluid first and the weather second. Trelleborg's comparison is the simplest guide: EPDM has excellent resistance to ozone, ageing and weathering, and good resistance to heat and chemicals, but it absorbs oil in a way that weakens its properties, so it is avoided with hydrocarbon, mineral or vegetable oils. NBR is the most commonly used elastomer for oils and has a limited tendency to absorb fluid hydrocarbons, but is more sensitive to ageing from environmental factors and abrasion.
For UAE use that splits the work cleanly. Outdoor seals in direct sun, cold room doors on a loading dock, chilled water and cooling water flanges, and rooftop enclosure seals favour EPDM. Fuel, lube oil and hydraulic fluid joints favour NBR, ideally kept out of direct sun. Trelleborg adds that NBR's weak points can be offset through formulation, so two NBR parts from different suppliers can behave differently. For high temperature and aggressive chemicals, other compounds such as fluoroelastomers and silicone come into play; check each against the fluid with the supplier's compatibility data.
Rubber is damaged by heat, ultraviolet light and ozone, and UAE warehouses and yards provide all three. Seals left in an uncovered container or on a sunlit shelf can crack or harden before they are fitted. ISO 2230 gives guidance on inspecting, recording, packaging and storing rubber products, assemblies and components before they go into circulation; the 2002 edition has been withdrawn and superseded by ISO 2230:2026, so ask your supplier which edition their storage procedure follows.
Fitting matters as much as storage. A new gasket on a damaged flange face will leak, and over-tightening a rubber gasket squeezes it out. Follow the bolt sequence and torque for the gasket type.
Rubber seals and gaskets are bought against a drawing, a catalogue size or an equipment standard, and there is no single UAE certificate for them as of 2026.
| Requirement | Applies to | Who sets it |
|---|---|---|
| ISO 3601-1 (O-ring dimensions and designation) | Standard round seals in the fluid power range | ISO, adopted as DIN ISO 3601-1 |
| Flange standards for flat gaskets | Gasket outside and inside diameters and bolt holes to match the flange | The piping specification; see our guide to pipe fitting and flange standards |
| Drinking water contact evidence | Gaskets, O-rings and washers in potable water fittings | The owner or utility; the UK WRAS scheme (BS 6920) is a common reference |
| ECAS or EQM conformity | Only where the item is part of a regulated product; see our ECAS and EQM guide | MoIAT |
| Oil and gas owner specifications | Elastomers in sour or high pressure service | The operator and its approved vendor list |
DIN lists ISO 3601-1 as covering O-ring inside diameters, cross-sections, tolerances and designation codes (current edition July 2026). Intertek states that WRAS materials approval covers rubber materials and components and also lists gaskets, O-rings and washers, with testing across all five areas of BS 6920. If your gasket will touch drinking water, ask the owner which evidence they accept before you order.
Supply comes from three routes: manufacturers and their agents for engineered seals, local rubber workshops that cut and mould to drawing, and stockists for standard sizes. Large seal makers such as SKF supply sealing products through distributors, which suits equipment spares where the original part number matters. Directories list rubber product workshops across Dubai, Sharjah, Ajman and Abu Dhabi; check each one's capability against your drawing, compound and quantity.
For related items see rubber mounts and vibration dampers and rubber expansion joints. To collect quotes, post your requirement with the drawing or sample photos.
Price follows compound, size, thickness, any fabric or metal insert, and the quantity. Moulded parts carry a tooling cost that is spread over the order, while cut gaskets from sheet have none and suit small runs. Special compounds for oil, high temperature or chemical duty cost more than standard EPDM or NBR.
Lead time is short when the part is cut from sheet in stock and long when tooling must be made or the part is imported. Imported goods clear through the Emirates' ports, and fast moving sizes are often held by stockists. Agree a sample approval step for moulded seals so a wrong dimension is found before the full batch is made.
Most wrong deliveries come from a vague request such as "rubber gasket, 6 inch". A complete enquiry names the flange standard and pressure class (or the drawing), whether the gasket is full face or ring type, the thickness, the compound and its hardness, the fluid and the operating temperature. If the part is a replacement, send the worn part or a clear photo beside a ruler, together with the equipment make and model.
Hardness is quoted on the Shore A scale, and a softer rubber seals better at low bolt load while a harder one resists extrusion at higher pressure. Fabric insertion makes a gasket stronger and limits stretch in larger sizes. Ask the supplier to state these on the quotation so you can compare like with like, and keep the datasheet with the maintenance record for the equipment.