Pliers and cutters are hand-operated gripping and cutting tools, from combination pliers and diagonal cutters to cable shears and hydraulic wire rope cutters. This page helps UAE buyers match the tool to the wire, cable or rope, check the insulation rating, find authorised brands and stockists, and understand price and delivery.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified pliers & cutters suppliers who quote for your order directly.
Tell us about pliers & cutters in UAE and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Pliers and cutters are hand tools that grip, bend or cut wire, cable, rope and small fasteners, and UAE crews buy them by the material they must cut and the hazard they work near. Electricians, instrument fitters, riggers, scaffolders and fleet mechanics all carry a different mix. They are part of the hand tools category for the UAE, next to wrenches and spanners and screwdrivers and hex keys.
| Type | Typical UAE use | What to specify |
|---|---|---|
| Combination and lineman's pliers | Electrical installation, general maintenance | Length, insulation to 1000 V, cutting edge hardness |
| Diagonal (side) cutters | Trimming copper wire, cable ties, instrument tubing | Soft-wire or hard-wire edge, flush or standard cut, insulated handle |
| Long nose and bent nose pliers | Panel wiring, terminals, tight access | Tip shape, serrations, spring return |
| Locking pliers | Holding, clamping, seized fasteners | Jaw shape, capacity, release lever |
| Circlip pliers | Bearing and gearbox maintenance | Internal or external, straight or bent tips, tip diameter |
| Ratchet cable cutters and shears | Copper and aluminium power cable, armoured cable | Maximum diameter, cable material, whether steel armour is included |
| Bolt cutters | Chain, padlock hasps, rod, mesh | Length, jaw hardness class, maximum material hardness |
| Wire rope cutters (impact, manual or hand-pumped hydraulic) | Rigging, lifting, elevator and marine work | Rope diameter and construction, new or used rope, power source |
For pipe and tube, a different set applies: see pipe wrenches and pipe cutters.
Choose by the material, its diameter and the voltage first, then by comfort and finish. A cutter used beyond its stated capacity chips the edge and can throw a fragment, so the capacity figure on the data sheet is a limit, not a guide.
ISO 5743:2021, the general requirements standard for pliers and nippers, states that it does not cover insulating or antistatic properties of handle coatings, and that plastic coatings and sleeves are for grip comfort. A comfort grip is therefore not an electrical rating. For work on or near live parts, specify tools made and tested to IEC 60900:2018 for up to 1000 V AC and 1500 V DC, and reject any tool with a cut or cracked sleeve.
Copper and aluminium cable cutters shear soft conductors and fail on steel wire; steel armour and wire rope need a purpose-built cutter. Morse-Starrett describes its wire rope cutters as designed for new and unused rope, and its range spans impact, manual and power-operated models up to 3-1/2 inch cutting capacity. That caveat matters in the UAE, where crews often cut used, oily or galvanised rope: confirm with the maker whether the model suits it. Hand-pumped hydraulic cutters such as Hydrashear reduce effort on large rope without a power source on site.
Pivot joints clog with sand, and steel left in a closed vehicle in summer gets too hot to hold. Wipe and oil pivots, store in a closed box, and for Jebel Ali, Khalifa Port and offshore yards ask for corrosion-resistant finishes on jaws and rivets.
No federal standard singles out hand pliers for sale in the UAE. Buyers specify against international tool standards and their own site rules. Table checked in October 2026.
| Requirement | Applies to | Authority or source |
|---|---|---|
| ISO 5743:2021 | General technical requirements for pliers and nippers, replacing the 2004 edition | ISO |
| ISO 5747:1995 | Dimensions and test values for lever-assisted side cutting pliers and diagonal nippers (older edition) | ISO |
| IEC 60900:2018 | Insulated pliers and cutters for live working up to 1000 V AC | IEC, called up by utility and site rules |
| Maker rated capacity | Wire rope and cable cutters, which have no single standard | Manufacturer data sheet |
| ADNOC Supplier Hub registration | Supply to ADNOC group companies | ADNOC |
| MoIAT regulated product list | Check before assuming a kit needs a certificate | MoIAT |
For vetting the trader behind a quotation, see how to source industrial suppliers in the UAE and Saudi Arabia.
Pliers reach UAE buyers through tool brand distributors, multi-brand industrial stockists and general trading companies; cable and rope cutters more often come through electrical wholesalers and rigging suppliers. For maintenance contracts, a counter near the site with next-day delivery often beats the lowest unit price.
On ListGCC, Morse-Starrett and Hydrashear cover wire rope cutters. General pliers ranges come from professional hand-tool makers such as Gedore, Facom, Teng Tools and King Tony. Ask each distributor for the insulation test marking on any 1000 V item. A parts list for a shutdown can be sent through post your requirement.
Price follows brand, steel quality, insulation rating and cutting capacity; lead time follows whether the item is a stocked catalogue tool or a special.
List the material, largest diameter, voltage and number of crews on the enquiry.