Vibration sensors in the UAE are the accelerometers, velocity sensors, proximity probes and transmitters that measure how rotating machines shake, so pumps, fans, compressors and turbines can be protected and maintained before they fail. This page sets out the sensor types UAE plants specify, how heat and humidity affect them, which standards and approvals apply as of 2026, which makers supply them, and what drives cost and delivery.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified vibration sensors suppliers who quote for your order directly.
Tell us about vibration sensors in UAE and receive competitive quotes from verified suppliers — free, fast, and no obligation.
A vibration sensor converts the motion of a machine casing or shaft into an electrical signal that a monitor, PLC or analysis software can read. They belong to the sensors and switches range for UAE industry and are bought by reliability engineers, maintenance contractors, OEMs and EPC contractors fitting out utilities and process plants.
| Type | Typical UAE use | Key specification points |
|---|---|---|
| Piezoelectric accelerometer | Condition monitoring of motors, pumps, fans and gearboxes, with online systems or portable data collectors | Sensitivity, frequency range, mounting thread, connector, IEPE supply, temperature limit |
| Velocity sensor | Casing vibration on fans, cooling tower drives and general machinery | Sensitivity, frequency response, piezo or moving-coil design |
| Eddy-current proximity probe system | Shaft vibration and axial position on turbines and compressors with fluid-film bearings | Probe diameter, linear range, extension cable length, driver, API 670 compliance |
| 4 to 20 mA vibration transmitter | Overall vibration into a PLC, DCS or BMS for alarms on pumps and fans | Measured quantity (velocity RMS or acceleration), range, loop power, alarm handling |
| Wireless vibration sensor | Balance-of-plant machines that do not justify cabling | Protocol (WirelessHART, ISA100, LoRaWAN), update rate, battery life, Ex rating |
| Vibration switch | Simple trip on cooling tower fans and small machines | Trip level, delay, reset, contact rating |
Eddy-current probes should not be confused with the inductive proximity sensors used for presence detection: both use a magnetic field, but a vibration probe outputs a calibrated gap voltage rather than an on/off signal. Machines fitted with vibration sensors often also carry encoders for speed feedback, and the tilt and inclination sensors page covers angle measurement on mobile plant.
Most UAE demand comes from utilities and process plants with large populations of rotating equipment running around the clock.
Heat limits the sensor and its electronics, and coastal humidity attacks connectors and cables. Check the operating temperature on the datasheet against the casing temperature of the machine in summer, not the air temperature.
As of 2026, vibration sensors in the UAE are chosen against international vibration and machinery protection standards, with ECAS-Ex certification required for any sensor installed in a hazardous area. We checked these references in October 2026.
| Requirement | Applies to | Authority or source |
|---|---|---|
| ISO 20816-1:2016 | General guidelines for measuring and evaluating machine vibration | ISO |
| ISO 20816-3:2022 | Industrial machines above 15 kW running between 120 and 30,000 r/min, measured in situ; replaced ISO 10816-3 and ISO 7919-3 | ISO |
| API Standard 670, 6th edition (July 2025) | Machinery protection systems: radial shaft vibration, casing vibration, axial position, overspeed and critical temperatures | American Petroleum Institute, via owner and EPC specifications |
| ECAS-Ex (Cabinet Decision No. 23 of 2016) | Sensors and transmitters in explosive atmospheres | MoIAT, on IECEx test report, certificate and QAR |
Tender documents still citing ISO 10816-3 should be updated to ISO 20816-3:2022, which also excludes most pump types and gas turbines above 3 MW, so check which part covers your machine. API 670 is a purchasing specification, not a certification, so ask the vendor to state compliance clause by clause. ECAS-Ex applicants submit the IECEx test report, test certificate and quality assessment report; the ECAS and EQM conformity guide explains the process, and oil, gas and petrochemical equipment in the UAE covers the wider hazardous area rules.
Vibration sensors in the UAE are imported and sold through authorised distributors, system integrators and the makers' regional offices, often as part of a monitoring system rather than as loose parts.
When a probe, cable and driver come from different makers, the calibration of the chain is no longer guaranteed, so buy proximity systems as matched or interchangeable sets from one source. Wireless sensors also need a gateway; see industrial wireless access points for the network side.
Price depends on the sensor type, frequency range, temperature rating, Ex certification and whether the sensor is wired or wireless; lead time depends on UAE stock and on how much of a monitoring system must be engineered around it.
Ask suppliers to confirm brand authorisation, UAE stock, the datasheet and the ECAS-Ex certificate number where needed. The guide to sourcing industrial suppliers in the UAE and Saudi Arabia has a fuller checklist, and you can post your requirement for vibration sensors to get quotes.