Crystalline waterproofing in Saudi Arabia is a chemical treatment for concrete, supplied as a mix admixture or a brush-on slurry, that forms insoluble crystals in the pores and hairline cracks when water is present. This page covers the forms on the Saudi market, where they suit sabkha sites, tanks and metro structures, their limits in dry interior conditions, the references to specify, which brands to look at and what drives cost.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified crystalline waterproofing suppliers who quote for your order directly.
Tell us about crystalline waterproofing in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Rigid or flexible cementitious waterproofing, where each works (wet areas, tanks, pools, basements from the inside), how thick to apply it, how to cure it in Gulf heat and what to ask suppliers for.
How to waterproof basements under high water tables and concrete water tanks: positive vs negative side, pre-applied bonded sheets, crystalline and bentonite, joints and service entries, potable linings and dewatering.
Saudi engineers turn to crystalline treatments for underground tanks, basement rafts, utility tunnels, metro and rail boxes, and water and sewage structures, where the concrete is wet for most of its life. The product is part of the set of waterproofing systems used on Saudi projects, and often works as one layer of protection with others. On sabkha ground the outside face may also carry bituminous sheet waterproofing, while inside tanks a cementitious waterproof slurry may be added. Information here was checked as of October 2026.
Crystalline waterproofing works by reacting with water and cement hydration products inside the concrete to form crystals that fill capillary pores and fine static cracks. It needs water to act, so it performs where the concrete is damp or under water pressure.
Makers describe the process in similar terms. Master Builders Solutions says its MasterLife 300D admixture reacts with water and calcium hydroxide to form non-soluble crystals and pore-blocking precipitates after the concrete has passed its plastic state, and lists potable water tanks, sewage plants, foundations and tunnels among its uses. Fosroc describes Supercast CWA as a chloride-free crystalline admixture in water-soluble bags for structures under sustained water pressure. Crack sealing claims (0.4 mm for those two products) refer to static cracks with water present.
| Form | Where Saudi projects use it | Specification points |
|---|---|---|
| Admixture batched into concrete | Raft foundations, basement walls, ground water tanks, metro and utility boxes, treatment plant tanks | Dose per cubic metre, PRAH classification, compatibility with other admixtures, trial mix |
| Crystalline slurry or coating | Existing leaking structures, inside of tanks and pits, repair of old concrete | Coats, surface preparation to open pores, damp curing period |
| Crystalline repair mortar and plugs | Tie holes, honeycombing, active leaks before coating | Setting time, compatibility with the slurry |
In Saudi practice the admixture route dominates on new structures because it comes with the ready-mix concrete and avoids a separate site layer that must be protected during backfill.
Choose crystalline treatment for concrete that will stay wet or hold water: below-ground structures on coastal sites, tanks, reservoirs and water and sewage structures. Think twice for roofs, above-ground slabs and dry interior basements that only see occasional water.
On the Eastern Province coast and low Red Sea sites, foundations sit in salty, wet ground that keeps the concrete damp, which is the condition crystalline treatments need. They reduce the permeability of the concrete, but the mix must also be designed for sulphate and chloride exposure with suitable cement and concrete admixtures, and many consultants add an external membrane for higher grades of dryness.
In Riyadh and other inland cities with deep, dry groundwater, a basement may see water only from irrigation or a burst pipe. Sika's data sheet for Sika WT-200 P says crystal formation needs water and recommends a hydrophobic admixture where concrete is generally dry or goes through wet and dry cycles. Match the chemistry to the exposure.
Crystalline concrete still leaks at badly made joints. Use waterstops and injection hoses at construction joints, and treat penetrations with sealants and sealing collars. The Sika data sheet calls for a binder content of at least 350 kg/m³ and a water to binder ratio no higher than 0.45, with curing started as early as possible; in Saudi summer that means night pours, cooled concrete and continuous wet curing.
Saudi specifications place crystalline products using BS 8102 and ACI 212.3R, and ask for the admixture standard, third-party certificates and test reports. Imports also go through SASO. The table lists them as of October 2026.
| Requirement | Scope | Source or authority |
|---|---|---|
| BS 8102:2022 Type B | Watertight concrete as a protection type for structures below ground | BSI code of practice |
| ACI 212.3R PRAH class | Admixtures for concrete exposed to water under pressure | American Concrete Institute report |
| BS EN 934-2 declaration | Concrete admixture performance; Sika WT-200 P cites Table 9 | European standard |
| BBA Agrément certificate | Independent assessment, for example 21/5849 for Fosroc Supercast CWA | British Board of Agrément |
| SABER certificates for imports | Imported products under a SASO technical regulation | SASO |
| Saudi Building Code | Concrete durability and foundation design | Saudi Building Code Center |
The Penetron summary of ACI 212.3R-10 notes that PRAN admixtures, the old damp proofing class, are not meant for water under pressure. For tanks and deep foundations ask for PRAH evidence and penetration test reports, such as BS EN 12390-8 or DIN 1048-5, on the exact product and dose. Admixtures imported into the Kingdom need the SASO route confirmed by the importer; see our guide to SASO SABER certification.
In Saudi Arabia crystalline admixtures are usually supplied by construction chemical makers through the ready-mix producer, with slurries sold through distributors and applied by approved contractors.
Brands in our directory to consider include Master Builders Solutions MasterLife 300 crystalline admixtures, Sika WT-200 P, part of Sika's watertight concrete approach and Fosroc Supercast CWA crystalline admixture. The data sheets cited on this page are Australian and UK editions, so ask each maker's Saudi office for the local data sheet and confirm the product is sold in the Kingdom before it is specified.
Get the maker and the ready-mix plant to agree the dose, mixing time and dispensing record for each truck, the trial mix results, the joint details and who inspects them, and the warranty conditions. For water tanks and reservoirs that will hold drinking water, also ask for a drinking water approval covering the treated concrete or slurry. Our guide to sourcing industrial suppliers in Saudi Arabia covers company checks.
The admixture cost follows concrete volume and dose, while the full price of watertight concrete also depends on joints, inspection and the mix changes it needs.
When you post your requirement, include concrete volumes, groundwater level and the city so suppliers can quote on the same basis.
Which waterproofing membrane suits basements, roofs, wet areas and tanks in the Gulf, the Dubai and Saudi rules that apply, how to test an installation, the brands with a regional footprint and what to put in an RFQ.