Copper pipes and tubes in Saudi Arabia are seamless drawn copper tube, supplied as coil or straight lengths, for air conditioning refrigerant lines, potable water, heating, gas and medical gas. This page explains the GSO and EN standards Saudi specifications quote, how to choose temper, size and wall, how heat and dust affect installation, and where to source tube.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified copper pipes & tubes suppliers who quote for your order directly.
Tell us about copper pipes & tubes in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Saudi projects buy copper tube to EN 1057 for water and gas, EN 12735-1 or ASTM B280 for air conditioning and refrigeration, and often name the Gulf Standard adoption for water tube. Tube sits in copper products in Saudi Arabia and is jointed with the fittings described on copper pipes and fittings.
| Standard | Use | Key facts |
|---|---|---|
| GSO EN 1057 | Water and gas in sanitary and heating work | Seamless round tube, 6 to 267 mm outside diameter; listed as a current Gulf Standard, approved 12 October 2011 |
| EN 12735-1:2020 | Air conditioning and refrigeration piping | 3 to 219 mm outside diameter; Cu-DHP in straights or annealed coil, CuFe2P straights only |
| ASTM B280 | AC and refrigeration field service | Common in US-based equipment specifications |
| GSO EN 1254-1:2024 | Capillary fittings for copper tube | Fittings with ends from 6 to 108 mm, approved 14 October 2024 |
The GSO record for EN 1057 lists uses including hot and cold water, heating, domestic gas and waste water sanitation. The record for EN 1254-1 covers the fittings, which the standard says are designed for a service life of up to fifty years. ASTM B280 is the matching US standard, and the Swedish standards body confirms SS-EN 12735-1:2020 as valid.
For other piping, compare pipes and fittings, PPR pipes and fittings and PVC pipes and fittings.
Choose the standard first, then outside diameter and wall from the equipment or hydraulic design, then temper from the installation method. Soft annealed coil bends by hand for small lines, while hard-drawn straight tube is used for larger runs that need support.
Typical Saudi uses are VRF and VRV systems, chillers and district cooling branches, hospital medical gas systems and plumbing and sanitary work.
Saudi summer heat, dust and humid coastal air affect handling, brazing and insulation more than the tube itself. Rooftops in Riyadh reach very high surface temperatures, while Jeddah and the Eastern Province add condensation and salt.
Copper tube is one of five copper product lines. Power distribution uses copper bus bars, flat fabrication uses copper sheets and strips, and machined valve and fitting bodies are usually brass products. Keep these separate in an enquiry so each supplier quotes the right material, and do not assume a tube stockist also holds bar or strip.
Joints decide whether tube stays leak-free. Brazed joints with the right filler suit refrigerant and high-pressure lines, soft-soldered capillary joints suit potable water within their pressure limit, and press fittings speed up site work if the tube is clean, round and cut square. Whatever method you use, specify the fitting standard together with the tube, and cut tube ends square and deburr them before assembly.
On large Saudi projects the tube often arrives months before installation. Agree storage conditions in the contract, record the batch numbers against the certificates, and inspect a sample on arrival at site for dents, ovality and contamination. Fixing a problem at the warehouse is far cheaper than finding it after the ceiling is closed.
Copper tube is bought to product standards in the contract, and approvals depend on the project owner and the water or building authority. Checked as of 2026, the points below usually apply.
| Requirement | Applies to | Authority |
|---|---|---|
| GSO or EN product standard | Tube named in the specification | GSO; project consultant |
| SASO and SABER | Regulated products entering the Saudi market | SASO |
| Water authority or owner material approval | Potable water installations | The relevant utility or owner |
| Medical gas and fire standards | Hospital and fire-related systems | Health, civil defence and project authorities |
| Aramco or owner vendor approval | Supply to energy projects | The asset owner |
The SASO and SABER guide explains which products need conformity certificates; ask the consultant whether your tube is covered.
Saudi supply comes from tube makers and agents, HVAC and plumbing stockists in Riyadh, Jeddah and Dammam, and importers bringing coil and straights through Jeddah Islamic Port and King Abdulaziz Port. Makers with copper tube lines listed here are KME, Wieland, Mueller, Cupori, ElvalHalcor, Mettube, Mehta Tubes, Golden Dragon and Maksal.
The sourcing guide compares manufacturer, distributor and stockist routes, and you can post your requirement with standard, outside diameter, wall, temper and quantity.
Price follows the copper market plus conversion for diameter, wall, temper, insulation and coating. Stock sizes ship quickly, while large diameters and special walls need a mill order.