Joint fillers in Saudi Arabia are the compressible filler boards and backer rods that fill expansion, isolation and contraction joints in concrete and masonry beneath the sealant. This page lists Saudi joint filler suppliers and explains which board suits roads, slabs, tanks and sewage works, why bitumen boards and elastic sealants clash, how to size backer rod, and what affects cost and delivery across the Kingdom.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified joint fillers suppliers who quote for your order directly.
Tell us about joint fillers in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Saudi projects use three groups of joint filler: preformed boards cast into expansion and isolation joints, round backer rods inserted before sealing, and bond breaker tapes for shallow joints. They are bought with the sealant as part of sealants and adhesives in Saudi Arabia, often by the concrete or flooring subcontractor. Crack repair mortars and tile grouts are separate products and not covered here.
| Filler | Saudi applications | What to specify |
|---|---|---|
| Bitumen impregnated fibreboard | Road and pavement joints, external slabs, culverts and retaining walls on infrastructure work | Thickness, ASTM D1751 compression and recovery data, bituminous or no top sealant |
| Closed cell cross-linked polyethylene board | Water and wastewater structures, desalination and treatment plants, basements, podiums, blockwork | Non-absorbent closed cell foam, no bitumen, compression recovery, sheet thickness |
| Closed cell polyethylene backer rod | Floor, facade and precast joints sealed with polyurethane or silicone | Rod diameter versus joint width, sealant maker's approval |
| Open cell polyurethane backer rod | Irregular joints in refurbishment and internal work | Compression range, keep dry before sealing |
The top sealant decides the filler. Concrete floor and pavement joints in the Kingdom usually take polyurethane sealants, facade and glazing joints take silicone sealants, and structures with large movements such as bridges move up to engineered bridge expansion joint systems.
Because bitumen in fibreboard can attack elastic sealants, the filler must be chosen for the sealant above it, not just for the joint width. Get this wrong and joints that pass handover fail within a few hot seasons.
Fosroc's technical data sheet for Cellflex, its bitumen impregnated fibreboard sold in Australia, states that the board must not be used under any joint sealant other than a bitumen based one, as mobile bitumen fractions are likely to degrade elastomeric sealants. Fosroc's Bitucell, with a product data sheet for Saudi Arabia, is the same class of product: a compressible filler and protection board made from bitumen impregnated wood fibres. Confirm the restriction on the Saudi data sheet of whichever board you buy.
For joints sealed with polyurethane or silicone, and for any joint in contact with water, Saudi specifications usually move to closed cell polyethylene. Fosroc's Hydrocell XL, also with a Saudi data sheet, is described as a bitumen-free, non-tainting, rot-proof, cross-linked closed cell sheet that supports the sealant and acts as a bond breaker. Sika's GCC data sheet, which lists Sika Saudi Arabia offices in Riyadh, Jeddah, Dammam and Rabigh, describes Sika FillerBoard-50 PE as non-absorbent and suitable for structures holding potable, salt, chlorine or sewage water.
Inland heat and dust, saline groundwater near the coasts, and long gaps between casting and sealing are the conditions that matter for joint fillers in Saudi Arabia.
Size the backer rod larger than the joint and set its depth from the sealant data sheet. Soudal's data sheet for its open cell PU backer rod gives a diameter up to 50 percent larger than the joint width, and says the rod stops three-point adhesion and controls joint depth.
The sealant's width to depth ratio then sets how deep the rod goes; Sika, for example, gives 1 : 0.8 for Sikaflex PRO-3. Where a full-depth board was cast in, cut it back to form the sealing groove, then insert rod or tape so the sealant does not bond to the board.
Joint fillers in Saudi Arabia are specified by the project documents and the manufacturer's data, with ASTM test methods named for board properties. As of 2026, no SASO technical regulation specific to joint filler boards or backer rod could be confirmed; importers should check their HS code with a SASO-approved notified body.
| Requirement | Applies to | Who sets it |
|---|---|---|
| ASTM D1751 compression and recovery | Bitumen fibre expansion joint filler boards | ASTM, named in data sheets and specifications |
| Bitumen-free, closed cell, non-absorbent board | Water, wastewater and desalination structures | Owner or utility specification and the consultant |
| Approved backing for the chosen sealant | All sealed joints | Sealant manufacturer |
| Conformity certificates through SABER where a technical regulation applies | Imported regulated products | SASO and its notified bodies |
See the SASO and SABER certificate guide for how product and shipment certificates work, and the Saudi sealants and adhesives overview for the SASO adhesive regulation and sealant test methods.
Construction chemical companies supply joint fillers together with their sealants on Saudi projects, while building materials traders in Riyadh, Jeddah and Dammam sell sheets and rod for smaller jobs. Makers carried on ListGCC with joint filler products include:
Before ordering, ask for the data sheet showing compression, recovery and water absorption, the thicknesses and diameters held in the Kingdom, and written confirmation from the sealant maker that the filler suits its product. Our guide to sourcing industrial suppliers covers wider checks. To get comparable quotes, post your requirement with filler type, thickness, quantity and site location.
Material and thickness set the price per sheet; volume, stock location and distance set delivery. Because boards are bulky and light, transport is a large share of cost on small orders to remote sites.