Spray foam insulation in Saudi Arabia is polyurethane foam mixed and sprayed on site into a jointless rigid layer, used mostly on concrete roofs of villas and apartment blocks, on tanks and in cold rooms. This page lists Saudi spray foam applicators and suppliers and explains the foam and coating specification, the EN and ASTM standards behind it, SASO rules, site checks for Riyadh heat and coastal humidity, and cost drivers.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified spray foam insulation suppliers who quote for your order directly.
Tell us about spray foam insulation in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Spray foam is rigid polyurethane or polyisocyanurate foam formed in place: an applicator meters two liquid components through a heated hose to a mixing gun, and the mix expands on the roof or wall and cures into a closed-cell layer stuck to the surface. It belongs with the other product groups under thermal insulation suppliers in Saudi Arabia, but a Saudi buyer is really purchasing a service, so choosing the crew matters as much as choosing the chemistry.
Saudi demand comes from flat concrete roofs on houses and apartment buildings, where insulation is compulsory and the roof is the largest heat gain, and from retrofit work where existing roofs must be insulated without adding much weight. A 2019 study on Saudi residential compliance with the energy code even found an external insulation system using polyurethane the most feasible wall option among those it compared.
| Use | Where it appears in Saudi Arabia | Specification points |
|---|---|---|
| Exposed roof foam with elastomeric coating | Villas, schools, mosques and warehouses in Riyadh, Qassim and the Eastern Province | Applied density, minimum thickness, slope to drains, coating type and dry film thickness |
| Foam beneath screed, tiles or pavers | Roofs used as terraces or carrying equipment | Compressive strength, separation layer, compatibility with the waterproofing |
| Tanks and vessels | Rooftop and ground water tanks, chilled water tanks, process vessels in Jubail | Service temperature, primer, outer UV and impact protection |
| Cold rooms, sheds and soffits | Cold stores in Jeddah and Dammam, steel buildings, retrofits | Closed-cell content, fire class and any covering the fire strategy needs |
Boards remain the better option in some cases. Factory-made PIR and PUR insulation boards give plant-controlled density and thickness; extruded and expanded polystyrene boards suit inverted roofs and walls; and non-combustible stone wool insulation is chosen where fire rules exclude foam. Roof foam is often specified alongside waterproofing systems in Saudi Arabia, and whole build-ups appear under roof insulation.
Saudi spray foam fails mostly through moisture during application, a thin or worn coating, and poor drainage. Each region adds its own risk: dew and humidity on the coast, heat and dust inland.
Morning dew and humid air can leave a film of water on a concrete roof that stops the foam bonding. A public US Veterans Affairs specification for sprayed polyurethane roofing requires a plastic sheet moisture test on concrete at the start of each day and each roof area, and no spraying if moisture condenses under the sheet. Ask the applicator for the substrate and weather window of their system and how they record it.
Ultraviolet light degrades uncovered polyurethane, so foam on a Riyadh roof must be coated or covered without delay. The same specification allows no foam to stand overnight without a base coat, uses a silicone two-coat system with a light top coat, and sets a total dry film thickness of at least 0.5 mm. Dust between lifts weakens adhesion; the specification sprays in 13 mm lifts with at most four hours between them.
Foam can be used to build falls, but ponding water attacks the coating. The finished surface should drain freely, with the minimum thickness held at drains.
As of 2026, spray foam in Saudi Arabia sits under SASO's thermal insulation and building materials regulations, while its properties are declared to EN 14315-1 or ASTM C1029. Because the foam is made on site, buyers need documents for the spray system, not just for the chemicals as shipped; confirm with SASO how your product and its HS codes are treated.
| Requirement | Applies to | Authority or body |
|---|---|---|
| SASO thermal insulation standards and technical regulations, mandatory from 25 November 2014 | Local and imported insulation products: dimensions, conductivity, water absorption, compression and fire, with a technical label | SASO |
| Building Materials Technical Regulation, part two | Insulation and cladding materials used in buildings | SASO and market surveillance authorities |
| EN 14315-1 | The spray system for in situ rigid PUR and PIR foam, before installation | CEN |
| ASTM C1029, with ASTM D1622 and D6694 | Spray-applied rigid polyurethane (Type III for roofing in the cited specification), in-place density, and silicone roof coatings | ASTM International |
| SBC 602 energy conservation, residential | Maximum heat transfer through roofs and walls of new homes, by climate zone | Saudi Building Code National Committee |
EN 14315-1 is written for the spray system before installation and excludes factory-made boards, while BS EN 13165 for boards excludes in situ foam, so a board certificate cannot stand in for a spray foam one. Research on SBC 602 notes that it divides the Kingdom into three climate zones, each with a maximum overall heat transfer coefficient, which sets the foam thickness the designer needs. For imported chemical systems, our guide to SASO and SABER certificates explains the conformity route.
The Veterans Affairs specification provides a sampling plan Saudi consultants can borrow: two cores for roofs up to 929 m2 and one more per further 929 m2, tested for thickness, density, compressive strength and cell structure, and six coating slit samples per 929 m2. It gives an in-place density of 44.9 to 48.1 kg/m3 for Type III roof foam.
Spray foam in Saudi Arabia is supplied by applicators who buy two-component systems from foam system houses, either produced in the region or imported, and spray them under their own or the maker's warranty. Ask to see roofs the crew completed at least a few summers ago.
Applicators are listed under insulation contractors in Saudi Arabia; our sourcing guide covers RFQ structure. With roof areas and drawings ready, post your requirement to receive comparable quotes.
Saudi spray foam is quoted per square metre at a stated thickness, so area, thickness, density and the coating decide most of the price. Site work around the foam can add as much again.
Ask applicators to state thickness, density, coating and dry film thickness in every quote.