PIR and PUR insulation in Saudi Arabia is rigid closed-cell polyurethane foam bought as boards, pipe sections and blocks for chilled water networks, cold stores, ducts and roofs. This page lists Saudi suppliers of PIR and PUR insulation and covers how the two foams differ, which SASO rules and product standards apply, how Riyadh, Jeddah and Eastern Province conditions change the specification, and what sets cost and lead time.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified pir & pur insulation suppliers who quote for your order directly.
Tell us about pir & pur insulation in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
In Saudi Arabia, PIR and PUR foams are used mainly for cold service and roofs: chilled water pipework in malls, hospitals and housing compounds, cold stores and food warehouses, refrigerant lines, pre-insulated ducts and flat roof boards. They sit within thermal insulation suppliers in Saudi Arabia, alongside mineral wool and polystyrene, and this page looks only at the factory-made foam products.
Both are closed-cell foams from the reaction of a polyol and an isocyanate. Polyisocyanurate (PIR) uses more isocyanate than polyurethane (PUR), which generally improves fire behaviour and temperature resistance. The European building board standard, BS EN 13165, counts both as "PU", so a Saudi buyer must ask which one is quoted.
| Product | Where Saudi projects use it | Key points to specify |
|---|---|---|
| Pipe sections, elbows and tees | Chilled water networks in Riyadh towers and compounds, cold water and refrigerant lines | Outside diameter, thickness, closed-cell content, vapour retarder jacket, fabricated fittings |
| Support inserts (high density) | Pipe hangers, clamps and saddles on cold lines | Density, length, thickness equal to the line insulation |
| Foil or tissue faced boards | Roofs on steel and concrete buildings, floors and walls of cold rooms | Aged conductivity, compressive strength, facing, tested fire class |
| Foam blocks | Raw material for fabricators making tank, vessel and fitting covers | Density, size, PIR or PUR chemistry |
| Pre-insulated duct panels | Supply and return ducts in commercial buildings | Panel thickness, facings, fire class, joint system |
Other products cover what foam does not. Stone wool insulation is chosen for hot lines in Jubail and Yanbu and for fire-rated walls, while glass wool duct wrap and rolls is the lower-cost option for ducts and ceilings. Inverted roofs and below-slab work usually take XPS and EPS polystyrene boards, and a jointless roof layer is done with sprayed polyurethane foam. Wall and roof panels with a factory foam core are listed under insulated metal panels in Saudi Arabia.
The main risk for foam on Saudi cold lines is condensation in humid coastal cities, while on roofs inland the risk is heat and sun. A specification that suits Riyadh may need tighter vapour sealing in Jeddah or Dammam.
Humid sea air means chilled water pipes sit below the dew point for much of the year. Insist on a factory vapour retarder jacket, sealed longitudinal and circumferential joints, sealed terminations at valves and flanges, and high-density inserts at supports so clamps do not crush the foam. One public specification from the US Veterans Affairs department sets a minimum insert density of 48 kg/m3 for polyisocyanurate supports on cold pipe, a useful benchmark when comparing Saudi quotes.
Dry air reduces condensation risk, but rooftop pipework and boards under membranes see intense sun and dust. Outdoor sections need metal or UV-resistant jacketing, and roof boards need compressive strength for plant and foot traffic. Never leave foam boards or sections uncovered on site; sunlight degrades unprotected foam.
Cold rooms in Jeddah, Riyadh and Dammam logistics zones run below freezing, where even small gaps let moisture freeze into the insulation. Seal every penetration and use the maker's tested jointing system.
Foam is combustible, so check the fire class of the exact product and facing against the building's fire strategy. Smoke matters indoors as well as flame spread: the Veterans Affairs specification notes that its polyisocyanurate pipe insulation does not meet a 50 smoke rating and confines it to exterior pipework.
As of 2026, foam insulation sold in Saudi Arabia falls under SASO technical regulations for thermal insulation and building materials, with imports certified through SABER, while product properties are declared to European or ASTM standards. Check the current regulation and HS code mapping with SASO before you order, as the sources below include older announcements.
| Requirement | Applies to | Authority or body |
|---|---|---|
| SASO thermal insulation standards and technical regulations, mandatory from 25 November 2014 | Local and imported thermal insulation products: dimensions, conductivity, water absorption, compression and fire, with a technical label | SASO and market surveillance teams |
| Building Materials Technical Regulation, part two on insulation and cladding | Insulation and cladding materials for buildings; non-conforming products may not be made, imported or displayed | SASO |
| SABER Product and Shipment Certificates of Conformity | Imported regulated products, by HS code | SASO, through approved certification bodies |
| BS EN 14308:2015 | PUR and PIR pipe sections, segments, boards and blocks for equipment and industrial installations, at least 90% closed cells | BSI / CEN |
| BS EN 13165:2012+A2:2016 | PIR and PUR boards for the building fabric | BSI / CEN |
| ASTM C591 | Unfaced preformed polyisocyanurate insulation on ASTM-based specifications | ASTM International |
SASO said in November 2014 that the thermal insulation regulations cover all local and imported products and that every product must carry a label with its technical information. In April 2018 SASO reviewed the Building Materials Technical Regulation, whose second part deals with insulation and cladding. For importers, our guide to SASO and SABER certificates explains the Product and Shipment Certificates. On the engineering side, BS EN 14308 covers roughly minus 200 °C to plus 200 °C, and the Veterans Affairs specification describes ASTM C591 Type IV pipe insulation at 0.027 W/m.K at 24 °C, for use up to 149 °C.
Saudi projects buy PIR and PUR from foam producers in the Kingdom and the wider Gulf, from international brands through distributors in Riyadh, Jeddah and Dammam, and from fabricators who cut sections and fittings from blocks. Insulation contractors often handle the whole package on chilled water and cold store jobs.
Among brands, Kingspan makes PIR insulation in the region: Kingspan Insulation reported in January 2018 that its Dubai plant had begun producing the Thermaroof TR22 roof board with a PIR core. For supply-and-fix work see insulation contractors in Saudi Arabia, and for HVAC packages see duct and duct insulation suppliers.
For RFQ structure, read our guide to sourcing industrial suppliers in Saudi Arabia and the UAE. With a bill of quantities ready, post your requirement so several Saudi suppliers quote on the same terms.
In Saudi Arabia, foam insulation cost depends on chemistry, thickness, density and fabrication, and lead time depends on whether the item is made locally or must be imported and certified. Insulation is bulky, so distance from the plant or from Jeddah Islamic Port or King Abdulaziz Port in Dammam adds freight cost.
Ask suppliers to split material, fabrication, freight and certification so the cost drivers are visible.