Nickel alloys in Saudi Arabia are high-performance corrosion and heat resistant metals such as Inconel 625, Hastelloy C-276 and Monel 400, used for sour gas, seawater, desalination and petrochemical equipment. This page explains grades, how to match them to service, the standards and certificates that owners expect and what to check with suppliers in the Kingdom.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified nickel alloys suppliers who quote for your order directly.
Tell us about nickel alloys in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Nickel alloys are metals built on nickel with chromium, molybdenum, copper or iron added to resist corrosion, heat or both. In Saudi Arabia they are bought for gas processing in the Eastern Province, Red Sea desalination, Jubail and Yanbu petrochemicals and power. They form the premium end of the other non-ferrous metals range in Saudi Arabia.
| Alloy family | Typical Saudi use | Key specification points |
|---|---|---|
| Alloy 625 (UNS N06625) | Weld overlay, clad pipe, flare parts, seawater and sour service components | Form standard, heat treatment, mill certificate, ISO 15156-3 compliance for H2S |
| Hastelloy C-276 and C-22 | Flue gas desulfurisation, scrubbers, aggressive acids, hot brine | UNS number, wrought or cast, filler, solution anneal |
| Monel 400 (nickel-copper) | Seawater pumps, valve trim, fasteners, hydrofluoric service | Form, hardness, avoid oxidising acids |
| Incoloy 825 and nickel-iron-chromium grades | Acid and sour service tubing, heat exchangers | Pipe or tube standard, cold work limits |
| High temperature grades | Furnaces, burners, turbines | Creep and oxidation data, welding procedure |
Compare with stainless steel pipes and tubes, titanium products and alloy steel plates when the service allows, and see lead products and zinc products for the other non-ferrous metals.
Choose the alloy from the worst service condition: H2S and chloride in wet gas, hot seawater or brine, or acid in flue gas. A wrong grade fails quietly by cracking or pitting, so the selection is documented in the project material selection report.
ISO 15156-3 sets requirements for selecting and qualifying corrosion-resistant alloys against sulfide stress cracking, stress corrosion cracking and galvanically induced hydrogen stress cracking in oil and gas production with H2S. The 2020 edition, published 17 November 2020, is listed as under revision, and the standard states it is not necessarily suitable for refining or downstream equipment. Saudi Aramco and other operators also publish their own material specifications, so ask the owner which document governs.
Haynes International reports crevice tests in natural Atlantic seawater in which C-22 and C-276 showed no attack after 180 days, alloy 625 showed attack on half of creviced sides, and 316L was attacked on all creviced sides. It describes 625 as acceptable and the C-type alloys as optimum for seawater. These are maker test results; Red Sea and Arabian Gulf water are warmer and in places saltier, so rely on the project corrosion study.
HP Alloys lists weld wire for 625 as ERNiCrMo-3 to AWS A5.14 and describes high resistance to oxidation at elevated temperatures. Weld joints must be clean and welded with a qualified procedure; see welding services.
As of 2026 nickel alloys are bought to international product standards and owner specifications, with mill certificates for traceability. SASO and SABER rules apply to imported products that are on the controlled list; check whether your item or its assembly falls under them.
| Requirement | Applies to | Authority or owner |
|---|---|---|
| ASTM B-series product standards (B443 plate, B444 and B705 pipe, B446 bar, B564 forgings, B366 fittings for 625) | Alloy 625 material, per HP Alloys' listing | Purchase order |
| ISO 15156-3 (NACE MR0175) | Alloys in H2S service | Owner and project specification |
| EN 10204 3.1 or 3.2 certificate | Traceability to heat number | Purchase order |
| Positive material identification | Receiving inspection | Project quality plan |
| Aramco, SABIC and utility approved manufacturer and vendor lists | Critical plant materials | The owner |
| SASO and SABER conformity | Imported controlled products | SASO |
For imports see SASO and SABER certificates for industrial equipment in Saudi Arabia, and for flange and fitting rules see the pipe fittings and flanges standards guide and pipe fittings and flanges.
Saudi gas processing, refining, petrochemicals, power and desalination are the main buyers. Typical purchases are CRA-clad pipe, weld overlay material, heat exchanger tubes and plates (see heat exchangers for refineries), scrubber internals, pump parts and instrument tubing, and parts for desalination plants.
Choose on traceability and owner approval first. Ask for the original mill certificate, check positive material identification is done, and confirm the supplier is on the owner's approved list for the item.
Most problems come from vague ordering, not from the metal. An enquiry that says only Inconel can be filled with several grades, and the wrong one may look identical. Always give the UNS number, product form and standard, and ask for positive material identification on receipt.
Price follows the alloy's nickel and molybdenum content, product form and size, certification level and quantity. Lead time follows local stock or mill slots.
Post your requirement with alloy, UNS number, form, size, standard and certificate level, and use the guide to sourcing industrial suppliers in the UAE and Saudi Arabia to shortlist.