Injection molding machines in Saudi Arabia inject molten plastic into a closed mould to make caps, preforms, crates, pipe fittings, pallets and technical parts. This page compares hydraulic, hybrid and all-electric machines, explains clamp and shot sizing, covers 60 Hz power, heat and the SABER and ISO 20430 requirements as of 2026, and shows how to compare suppliers.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified injection molding machines suppliers who quote for your order directly.
Tell us about injection molding machines in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
The right machine follows the part. Large crates, pallets and drums suit big hydraulic or two-platen machines, packaging and closures suit fast servo-hydraulic or all-electric machines, and precision or medical parts suit all-electric. In plastic processing machinery, injection moulding supplies Saudi packaging, construction, automotive aftermarket, water-tank and consumer goods producers.
| Machine | Typical Saudi products | Strength | Limit |
|---|---|---|---|
| Hydraulic | Crates, pallets, buckets, large housings | Lower purchase price, high clamp force | Higher energy use, oil cooling |
| Servo-hydraulic or hybrid | Closures, containers, fittings | Lower energy use at moderate cost | More complex than fixed-pump models |
| All-electric | Medical, electronics, precision parts | Precision, clean operation, low power | Higher price, smaller tonnage range |
| Preform system | PET preforms | High cavity count | Specialised for one product family |
Pallets and crates made on these machines are described under pallets and crates, and pipe fittings under PP-R pipes and fittings. The part list is on injection molded parts, and the tool itself is in mold and die making. Preforms feed blow molding machines for bottles.
Check clamp force, shot size, mould fit and cycle time together. Clamp force must hold the mould shut during injection over the projected area of the part. The mould must fit between tie bars and on the platens. FANUC lists tie-bar spacing from 260 by 235 mm on its ROBOSHOT α-S15iB to 920 by 920 mm on the α-S450iB, which shows how widely platens differ across a range.
For a Saudi project, add three checks. First, ask for an estimated cycle on your mould drawing and the cooling water temperature it assumes. Second, ask for the machine's electrical design for 60 Hz. Third, ask what the control stores for traceability if you supply automotive or medical customers.
In Saudi Arabia, plant heat and the grid shape machine choice as much as tonnage. Summer ambient temperatures reduce the cooling water capacity that sets cycle time, and many machines are built for 50 Hz markets.
The Saudi grid runs at 60 Hz, while the wider GCC interconnection grid operates at 50 Hz, as the GCC Interconnection Authority notes. State the supply in the purchase specification so motors, drives and heaters are right from the start. FANUC says its servo technology and energy recovery cut ROBOSHOT power use by 50 to 70 percent against hydraulics; since this is a maker claim, request a measured kWh per kg for your part.
Size process chillers and cooling towers for summer peak. Humidity on the Red Sea and Gulf coast puts moisture into PET and nylon, so use hopper dryers and closed conveying. Dust is common in the central region; keep resin and regrind covered. Compressed air for ejection and automation comes from an industrial air compressor. Resin and colour sourcing is under plastic raw materials and masterbatch and additives.
Buyers specify ISO 20430 for machine safety and import each model through SABER. The GCC Standardization Organization adopted ISO 20430:2020 as GSO ISO 20430:2024, approved on 14 October 2024, and the GSO store lists it as sold through member country stores. As of 2026 the SASO regulation that applies to a given machine depends on its classification and HS code.
| Requirement | Applies to | Authority |
|---|---|---|
| GSO ISO 20430:2024 | Injection moulding machines with hydraulic or electric platen drives; excludes injection blow, reaction injection, compression and transfer machines | GCC Standardization Organization |
| SABER product registration and shipment certificate | Each imported machine model, via the importer of record | SASO |
| Product certification for what you mould | Closures, water-contact and food-contact parts, electrical housings | SASO and sector regulators, by product |
| SASO degradable plastics regulation | Disposable PE and PP items of 250 microns or less | SASO |
The degradable plastics rule is aimed at thin packaging rather than injection parts, but a moulder making thin disposable items should check its scope. Our SASO and SABER guide for industrial equipment explains what the certifier asks for in the machine's technical file.
Machines are sold through agents and offices of European, Japanese and Chinese builders, and a large used-machine trade. Brands on this site that make injection machines or systems:
Other builders sell through Saudi agents; compare local technicians, parts stock in Riyadh, Jeddah or Dammam, and training. Unloading automation is covered by industrial robots.
Ask every supplier to quote the same scope, including mould fit, robot, dryer, chiller, 60 Hz electrical design and installation. Request cycle estimates on your drawing, energy figures, and references in the Kingdom. Verify the agency letter and commercial registration as set out in the guide to sourcing industrial suppliers, and post your requirement to compare offers side by side.
Price follows clamp force, drive, automation and scope; lead time follows stock, mould making, SABER and shipping.