Encoders in Saudi Arabia are the rotary sensors that give drives, PLCs and motion controllers shaft speed and position on cranes, kilns, conveyors, mining equipment and packaging lines. This page explains how Saudi buyers choose between incremental and absolute encoders, which interfaces to specify, what heat and fine dust do to an encoder, which SASO requirements apply as of 2026, and how to buy.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified encoders suppliers who quote for your order directly.
Tell us about encoders in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
An encoder tells a controller how fast a shaft is turning or exactly where it is. Encoders belong to the sensors and switches family in Saudi Arabia, and Saudi buyers meet them on drive retrofits at cement and steel plants, on port and warehouse cranes in Dammam and Jeddah, on conveyors at phosphate and bauxite operations, and on food and bottling lines in Riyadh and Al Kharj.
| Encoder | Saudi use case | What decides the choice |
|---|---|---|
| Incremental, solid shaft | Speed feedback for VFD-driven conveyors, fans and kiln drives | Pulse count the drive card accepts, output level, coupling |
| Incremental, hollow shaft | Mounting directly on a motor non-drive end without a coupling | Bore size, torque arm, motor shaft fit |
| Absolute multi-turn | Hoist height and trolley position on cranes, reclaimers, gates | Turns counted, interface, retention of position at power loss |
| Fieldbus or Ethernet absolute | Networked packaging and logistics systems | PROFINET or EtherNet/IP, ring redundancy, cycle time |
| Safety-rated encoder | Safe speed limits on robots and lifting equipment | Certified SIL or PL level and compatible safety controller |
Where only a speed or end-position signal is needed, a cheaper sensor may do: proximity sensors counting teeth for overspeed, or limit switches at end of travel. Angle measurement on booms and solar trackers is often done with tilt and inclination sensors instead, and machine condition is watched by vibration sensors. Encoder signals end up in VFDs or servo drives.
If losing position after a power dip would stop the machine or force a homing run, buy absolute; if the drive only needs speed, incremental is cheaper and simpler. Grid disturbances, generator changeovers and emergency stops all cut encoder power, so on cranes and positioning axes absolute encoders save restart time.
Published figures give a sense of range. Rockwell's Bulletin 847 incremental encoders offer integer resolutions from 1 to 65,536 counts per revolution and replaced the older 844 and 845 bulletins; Omron's E6B2-C offers 20 to 2,000 pulses. For absolute encoders, Siemens states up to 65,536 steps per revolution and 16,384 revolutions on its PROFINET multi-turn model, and Rockwell's 842E offers 262,144 steps by 4,096 turns. When replacing an encoder on a drive, the pulse count and signal level must match the drive's encoder card settings exactly.
Name the interface the receiving drive or controller supports, then pick the most noise-tolerant version of it. Common choices:
Networked encoders bring OT security into scope on critical infrastructure; see industrial networking for switches and architecture.
Fine dust works into the shaft seal and bearings, and heat from motors and sun shortens electronics life, so check the shaft-side IP rating and the upper temperature limit. Siemens gives IP67 for the housing but IP64 for the shaft side on its PROFINET encoder, with a working range of minus 40 to plus 75°C. Rockwell's 842E is IP67 and runs from minus 30 to plus 85°C. Keep shaft loads within the datasheet (Siemens allows 40 N axial and 110 N radial at up to 6,000 rpm) by using a flexible coupling, and shade encoders on outdoor equipment where you can.
As of 2026, encoders imported into Saudi Arabia fall under SASO's conformity system through SABER, the Saudi RoHS regulation for control and monitoring instruments, and SASOEX where they are installed in hazardous areas. Check the HS code on SABER for the certificates needed.
| Requirement | Scope | Issuer |
|---|---|---|
| SABER product and shipment certificates | Regulated electrical products, by HS code | SASO, through approved certification bodies |
| SASOEX certificate | Encoders for explosive atmospheres, on IECEx or ATEX documents | SASO |
| Saudi RoHS technical regulation, Version 2 | Control and monitoring instruments and spare parts, with exclusions for large fixed installations | SASO notified bodies |
| IEC 61800-5-3:2021 | Safety-related encoders in drive systems where functional safety is claimed | IEC |
| IEC 60529 | IP ratings for housing and shaft seal | IEC |
The guide to SASO and SABER certificates covers the import steps. For Aramco, SABIC and Ma'aden work, also check the owner's approved manufacturer list.
Encoders reach Saudi sites through automation distributors, drive service centres that stock encoders for the drives they repair, and crane and machine OEMs. Brands frequently specified:
Cost rises with absolute multi-turn operation, Ethernet or safety interfaces, special shafts and Ex approval, and those variants are less likely to be held in the Kingdom, so lead time includes factory time plus SABER clearance. The supplier sourcing guide for Saudi Arabia and the UAE covers vendor checks, and you can post your requirement with the encoder code or its type, resolution, interface and shaft details.