Lubricants and greases in Saudi Arabia are the industrial oils and greases bought for plants, fleets, ports and oilfield sites in extreme inland heat and coastal humidity. This page compares oil with grease, explains ISO VG and NLGI grades, sets out the SASO lubricating oils regulation and SABER steps as of 2026, and points you to Saudi suppliers.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified lubricants & greases suppliers who quote for your order directly.
Tell us about lubricants & greases in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
Pick oil when the lubricant needs to flow, remove heat or be filtered, and pick grease when it has to stay put at a sealed bearing or an open joint. The two sit within lubrication and maintenance supplies in Saudi Arabia, and a typical plant in Jubail or Yanbu stocks both.
| Equipment | Normal lubricant | Note for Saudi sites |
|---|---|---|
| Motors, fans, pumps with sealed bearings | Grease | Heat on rooftop and desert-site motors shortens regreasing intervals |
| Gearboxes on conveyors, mills and crushers | Oil (gear oils) | Sump temperatures run high in summer, so check the viscosity index |
| Hydraulic units on cranes and presses | Oil (hydraulic oils) | Dust control at filler caps matters most |
| Air compressors and gas turbines | Oil (compressor oils, turbine oils) | Often specified by the operator's approved list |
| Open gears, chains, wire rope | Specialist compounds (industrial lubricants) | Choose a film that sheds sand |
| Drill pipe and casing connections | Thread compounds | Per the connection maker, see the greases page |
For the full oil range by application see lubricants and oils.
An ISO VG number is an oil's thickness at 40 degrees C, and an NLGI number is a grease's stiffness. Neither says anything about quality, so specify grade together with approvals and the base oil.
ISO 3448 defines the ISO VG series of viscosity grades. An oil rated VG 68 does not behave like VG 68 at a 90 degree C gearbox; the viscosity index tells you how much it thins. NLGI grades come from the cone penetration test in ASTM D217, from 000 (semi-fluid) to 6 (block). A trade source on grease selection notes that NLGI 2 covers the majority of industrial rolling bearings, with NLGI 3 considered for vertical shafts or heavy vibration, and that the grade says nothing about base oil viscosity. A grease for a slow, heavily loaded shaft can use a heavy base oil, so read the data sheet and match the bearing maker's requirement.
Saudi sites combine high inland temperatures, dust storms and long supply routes, so lubricant spoilage in storage and contamination at the filler point cause more trouble than the brand chosen.
Lubricants shipped by road to Riyadh or remote mine and solar sites can sit in hot trailers for days. Receive drums into shaded stores, check seals and dates, and avoid stacking pallets outside. Heat also pushes grease bleed and can separate lower grade products, so ask for batch records.
After a dust storm the filler necks, breathers and grease nipples of every machine on site are loaded with fine dust. Wipe before opening, use sealed transfer cans with filters, and fit desiccant breathers where moist coastal air meets hot gearboxes at Jubail, Yanbu and Dammam.
For crews working far from a depot, cartridges and small packs are easier to protect than a half-used pail. Conveyor and crusher lines often move to automatic delivery, as covered under lubrication systems, and personal protection for crews in the heat is covered in the heat stress PPE guide.
Saudi lubricating oils are regulated products: the SASO Technical Regulation for Lubricating Oils covers engine and several industrial oil types, and shipments clear through SABER with product and shipment certificates. The points below were checked in October 2026 against the English translation; only the Arabic text is binding.
| Requirement | What it means for the buyer | Authority |
|---|---|---|
| Certificate of Conformity under the lubricating oils regulation | Supplier holds type approval from a SASO-approved body before placing oil on the market | SASO |
| PCoC and SCoC through SABER | Product certificate per model and shipment certificate per consignment, requested by the importer | SASO, SABER platform |
| Container and labelling rules | Chemical product labelling, SI quantities and recyclable plastic markings | SASO, GSO |
| Automotive grease standard in Annex 1 | Applies to vehicle greases; industrial greases follow the buyer specification | SASO |
| Aramco supplier registration | Required to sell directly to Aramco | Aramco |
| NSF H1 registration | Called up by food and beverage plants | NSF, set by the buyer |
The regulation was revisited in 2023, when SASO held a workshop on proposed changes, and we did not confirm a revised text, so check the current version on SASO's site. The SASO and SABER guide walks through the platform. Used oil is a regulated waste; arrange collection with a licensed contractor through your environmental team.
Saudi supply comes from oil company distributors with blending or filling plants, importers of specialist greases, and MRO stockists in Dammam, Jubail, Riyadh and Jeddah. An authorised distributor can show the SABER certificates and batch records an importer must hold.
Brands to browse are Shell and Mobil for industrial oils and greases; Chevron, Texaco and Caltex from one group; Lubriplate for NSF H1 food-grade products; and Jet-Lube for thread and anti-seize compounds. Related needs are listed under rust preventives and penetrants and MRO consumables and kits. To confirm an agent's rights, read the sourcing guide.
Base oil, approvals and pack size drive price; stock in the Kingdom and SABER clearance drive delivery.
To gather like-for-like quotes, post your requirement with grades, approvals, sites and quantities.