Hot dip galvanizing in Saudi Arabia means immersing fabricated steel in molten zinc to form a bonded corrosion coating, normally certified to ISO 1461 or ASTM A123. This page covers how Saudi buyers specify thickness, plan around kettle size, combine zinc with paint, and judge price and lead time across the Eastern, Central and Western regions.
0 suppliers found
Skip the search. Post your requirement and we'll connect you with verified hot dip galvanizing suppliers who quote for your order directly.
Tell us about hot dip galvanizing in Saudi Arabia and receive competitive quotes from verified suppliers — free, fast, and no obligation.
A Saudi buyer gets steel that has been pickled, fluxed and dipped in molten zinc, so every surface, inside tubes and behind welds as well as outside, carries a zinc layer bonded to the steel. It is one of the main routes in surface treatment in Saudi Arabia and it is ordered with a fabrication package for transmission steel, substations, pipe supports, gratings, fencing and building frames.
Two documents define the work. ISO 1461:2022 covers fabricated iron and steel dipped in a zinc melt holding no more than 2 percent other metals; it took over from the 2009 edition and leaves out continuously galvanized sheet and wire, tube from automatic plants and products with their own standard, such as fasteners. ASTM A123/A123M covers structural shapes, strip, bar, plate, pipe, tube, wire and rebar, singly or as assemblies.
| Product | Where it is used in the Kingdom | What to write in the order |
|---|---|---|
| Lattice towers, structural members | Power lines, substations, plants, warehouses | Standard, edition, minimum thickness by section |
| Pipe supports and racks | Jubail, Yanbu and Ras Tanura process areas | Standard plus venting and drain details |
| Gratings, handrails, stair treads | Walkways, platforms, public works | Whether the part is dipped as a panel or loose |
| Fencing, poles, signage frames | Roads, compounds, utilities | Pole length against kettle length, single or double dip |
| Parts for later coating | Facades, furniture, equipment frames | Duplex preparation to ASTM D6386 or D7803 |
Fabrication comes first: see metal fabrication services and structural steel suppliers. Galvanizing then protects what they make.
The steel section decides it, because ASTM A123 grades minimum thickness by steel thickness and category. For structural shapes the minimum average is 45 microns under 1.6 mm, 65 microns from 1.6 to under 3.2 mm, 75 microns from 3.2 to under 6.4 mm, and 100 microns at 6.4 mm and above. Strip, bar and plate reach 100 microns only above 16 mm.
These are floors. Heavy steel tends to carry more zinc than the grade requires. The finish has to be continuous and free from blisters, flux and heavy dross, and rejected work, other than for embrittlement, may be stripped and dipped again. Request the plant's thickness readings by batch, not a single certificate for the month.
Check venting, draining and size. The American Galvanizers Association states that design and fabrication are the responsibility of the designer and fabricator, and that the galvanizer needs customer approval for extra work such as drilling vent holes. Skipping this step is the usual cause of delays at Saudi plants.
It lasts well in both, but the rate of zinc loss differs and the specification should reflect the site. ISO 12944-2 sets out how to classify atmospheres by corrosivity, and Jubail, Ras Tanura, Yanbu and Jeddah sit in saltier, more humid air than Riyadh or Qassim. On the coast, specify a higher thickness or a duplex system for steel that is hard to maintain.
In a duplex system the zinc and the paint or powder coat protect each other. The American Galvanizers Association reports a service life of about 1.5 to 2.3 times the sum of the two coatings, and at least a 50 percent longer paint life over zinc. For the coating side, read powder coating services in Saudi Arabia; for steel too big for a bath, thermal spray coating is the alternative. Heavy blasting before paint is covered under shot blasting and sand blasting.
Quality is governed by the owner's specification more than by a single national certificate. Checked as of 2026, confirm current rules with your client and the relevant authority.
| Requirement | Applies to | Source of the requirement |
|---|---|---|
| ISO 1461:2022 or ASTM A123/A123M | Thickness, finish and testing of galvanized articles | ISO; ASTM International |
| Client coating specification | Approved vendors, duplex systems, witness points | Aramco, SEC, SABIC, EPC contractor or consultant |
| Third-party inspection | Thickness and adhesion verification | Inspection body nominated by the owner |
| Environmental permit | Acid, flux, dross and wastewater from the plant | National Center for Environmental Compliance |
Inspection options are covered under coating inspection in Saudi Arabia. For imported structural steel and certificates, the guide to SASO and SABER certificates for industrial equipment is a useful reference, though galvanizing quality itself comes from the project specification.
Pick by capacity, reach and records. Galvanizers are concentrated near Dammam and Jubail, with others around Riyadh and Jeddah, and trucking long steel across the Kingdom adds cost and handling damage.
The guide to sourcing industrial suppliers in the UAE and Saudi Arabia adds general vetting steps. To get comparable offers, post your requirement for hot dip galvanizing.
Price is quoted per tonne, with higher rates for small or complex work. Zinc price, steel weight, section thickness, double dipping and the plant backlog all matter. Projects that drop large tonnages at once, such as line and plant packages, can queue for weeks, so book capacity when the fabrication programme is set.
Allow time for inspection, repair of local defects, and transport. Protect galvanized steel in storage and loading with nylon slings and timber separators, because wet stacking of galvanized sections can leave white deposits on the zinc.